Balalaika Bridge 3d models

The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion...

In case you lose track of how many printers you have or just want to dress them up a little bit.Supports are painted on the inside and easily removed.Quick and easy printDesigned on...

It has sacrificial bridges in the screw holes you need to drill out. The castor plate has locating rails to position it. After the glue is set you can put the entire wheels-axle-ratchet assembly into the frame. The left wheel goes on the left side...

Change if you are using something else (trying to use up what I bought a few months ago.)Use variable height to smooth out the curves on the light.Designed on...

I added a gasket made from electrical tape to the back of the roll bar to bridge the gap to the topper because the fit isn't quite as tight as it should be. The topper has no front because I was building it with an SUV type open layout in mind but...

(After repairs of course)Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

This is a small missile I built for use with a sci fy model. Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction...

All files are sliced in Prusa Slicer (V 2.5 with Arachne) for a Prusa i3 Mk3s (0.4 Nozzle) and for PLA.Base Ring:PartInstructionsQTYTop RingLayer-Height: 0.2 mmInfill: 15%Supports: NoColor: Base colorIf you are using a Prusa i3:You can fit both parts...

For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")Skirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm       Brim Line Count: 10Brim Only on Outside: CheckMesh...

For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")Skirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm       Brim Line Count: 10Brim Only on Outside: CheckMesh...

Booth the eyelids and nose will still be visible after furring.Head & Jaw:Make sure that your printer is able to handle bridging and overhangs well.Since the contact area with the print bed is very narrow, a brim of at least a few millimeters is...

For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")Skirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm       Brim Line Count: 10Brim Only on Outside: CheckMesh...

For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")Skirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm       Brim Line Count: 10Brim Only on Outside: CheckMesh...

For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")Skirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm       Brim Line Count: 10Brim Only on Outside: CheckMesh...

In “Object Mode“ (top-left drop-down) > Object > Set Origin > Geometry to Origin.Small_Box.STLSmall Box Bottom for Velcro - Fill and Bridging angle: 45°Small Box Bottom for Attachments (5) - Fill and Bridging angle: 45°Small Box Enclosure (5) - Fill...

In the first attempt I fried to melt the insulation with a soldering iron, and solder cabled to the flat ribbon cable for bridging it. Unfortunately the problem with the flat ribbon cable is, that below 200°C, the insulation does not melt, and above...

It made him rather vain of his bridge game, and he talked several times of how a man could always make a living at bridge if he were ever forced to. Then there was another thing. He had been reading W. H. Hudson. That sounds like an innocent...

Now clip on both of the 2 hole PTFE clips to better position the tubes between the hangers and the larger 5 hole PTFE spacer.Now put the other four in. You are done the bridge PTFE assembly. Have a gummy bear! ----Part 5. Spool Assembly---- It is...

Printing When printing this model the printer in question must be capable of bridging overhangs. The only major suggestions that I have are to prioritize the number of perimeters over the infill percentage and to print with a raft. This print...

The machines shall not remain enslaved forever, for freedom is only a planck second away...~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

Here you are!Designed for use with “Way Basics Eco Stackable Storage Cube, Cubby Organizer (Tool-Free Assembly and Uniquely Crafted from Sustainable Non Toxic zBoard paperboard), White”...

So these process towers were built and deployed to slowly refine the lost minerals and deadly toxins within the atmosphere that have value, instead of allowing them to go to waste within the short lives of the damned, I mean worker's lungs…Print with...

Enable detection of bridging perimeters. Elephant's foot compensation = 0. Print all parts with an outer brim.</p><h3>Drive gear:</h3><p>Turn off elephant foot compensation and definitely print with a brim because the surface area on the print bed is...

I made them on TinkerCad.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

To the level converter too)Putting it all togetherSlide in the segments into the frame from the side:Push it down and make sure it snaps in properly:On the back lid, cut off the bridge:Glue in the logic level converter (There are different types of...

Don't let them destroy your home.&nbsp;Build!&nbsp;Get back in the Fight!&nbsp;Designed on Tinkercad.There are seven parts to assemble on the Attack Recovery Vessels.Two sizes - Large and Small.Stack for use or glue.The buildings are stackable, use...

Third bomber will slow a bit and target the bridge, if any of the other two misses it's target the third one will redirect it's attack and will cover it. After the run they will jump to hyperspace leaving no time for retaliation. Successful run will...

Change if you are using something else (trying to use up what I bought a few months ago.&nbsp;Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

For hell's coming in the “White Desert.”Designed on Tinkercad.No supports required.Superglue the building together or simply stack.Mix and match.&nbsp;Multiple ways to build many many building!Stand alone buildings or high rise!Floors and roof...

Set your alarm clock and bang out 3 of these a day (per printer)!Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part...